Motors & Blowers
Thermostats
Breakers
Pilot & Ignitors
All products
New
Goodman-Amana PCBBF162S Integrated Control Board
An OEM replacement integrated control board used in compatible Goodman and Amana HVAC equipment to control furnace operating functions as specified by the manufacturer.
Key Features:
- Official OEM integrated control board for Goodman-Amana HVAC equipment
- SupplyHouse lists this item as Product Type: Control Board
- SupplyHouse lists replacement/cross-reference part numbers: PCB00109, PCBBF109S, PCBBF109, 0130F00006S, PCBBF132S, PCBBF122S, PCBBF122, 0130F00006, PCBBF132
- Goodman's parts lookup shows PCBBF162S as a substitute part number for PCBBF132 on certain furnace models (listed as "PCB 2STAGE HYBRID FURNACE CNTL")
Compatibility & Applications:
- Intended for use only in Goodman/Amana equipment that specifies PCBBF162S (or its listed predecessor/substitute numbers) for that exact model/serial
- Goodman's parts lookup confirms PCBBF162S as the correct/substitute control board for certain furnace models, while other models use different boards (model-specific)
- Must only be used where the manufacturer specifies this exact part number: PCBBF162S
Installation & Operation Notes:
- Installation should be performed by a qualified HVAC service professional
- Refer to the specific unit's installation/service manual for wiring, setup, and checkout procedures (this part is model- and configuration-dependent)
- Confirm compatibility by furnace model/serial before installation to avoid incorrect operation or repeat failures
Maintenance & Troubleshooting:
- Typical service scenarios reflected in customer feedback include replacing the board to restore normal furnace operation after a no-heat/control failure
- If symptoms persist after replacement, confirm correct part number for the unit and continue diagnosis per the manufacturer's troubleshooting steps for the furnace
User Reviews & Q&A Summary:
- Reviews consistently report this as the correct OEM replacement that restores furnace operation, with many describing a direct-fit swap and immediate resolution
- Common themes include easy installation for experienced technicians/DIYers and strong value compared to other sources, with frequent mentions of fast delivery/availability
- Q&A themes focus on model-specific compatibility: it is confirmed compatible with some models and predecessor boards (e.g., PCBBF132), while other models require different boards (e.g., PCBBF140S), so model/serial verification is emphasized
- Robust Push Terminals
- Common-Sense LEDs
- Clean, Professional Installation
- Smaller Footprint
- Variable-Speed Fan Control
- Includes HZ311 TrueZONE panel, AT140 40VA transformer, C7735A discharge air sensor
Product Specifications
- Stages: Single Stage
- Operating Voltage: Input 24 Vac, 60 Hz
- Line Voltage: 115-230 Vac, 60 Hz
- Inducer Motor/Blower Motor: PSC
- Ambient Operating Temperature: -40 to 175°F (-40 to 80°FC)
- Humidity Range: 5% to 95% relative humidity (non-condensing)
Product Specifications:
- Description: 1/2 in. NPT x 1/2 in. NPT Intermittent Hot Surface Pilot Ignition SmartValve Control with fast-fast opening and 3.4 in. wc pressure regulator setting
- Flame Sense: Electrode
- Type of Gas: Natural
- Ignition System Type: Intermittent Hot Surface Pilot Ignition
- Ignition Sequence: Intermittent Pilot
- Ignition Source: Pilot
- Ignition Trials To Lockout: Continuous Retry
- PrePurge: None
- Body Pattern: Straight-through
- Opening Characteristics: Fast-Fast Opening
- Ignition Trial Time (sec): 90 sec
- Electrical Ratings: 24 Vac
- Frequency: 60 Hz; 50 Hz
- Flame Failure Response Time (sec): 1.6 sec @ 3 µA
- Ambient Temperature Range (F): -40 F to +175 F
- Ambient Temperature Range (C): -40 C to +79 C
- Pressure Regulator Setting (psi): 3.4 in. wc
- Pressure Regulator Setting (kPa): 0.87 kPa
- Pressure Ratings (psi): 1/2 psi
- Pressure Ratings (kPa): 3.45 kPa
- Inlet/Outlet Size (in.): 1/2 in. NPT x 1/2 in. NPT
- Maximum Capacity (ft³/hr): 200 ft³/hr
- Maximum Capacity (m³/hr): 5.7 m³/hr
- Minimum Capacity (ft³/hr): 20 ft³/hr
- Minimum Capacity (m³/hr): 0.6 m³/hr
- Maximum Capacity at 1 in. P.D. (ft³/hr): 150 ft³/hr
- Maximum Capacity at 1 in. P.D. (m³/hr): 4.2 m³/hr
- Pilot Gas Outlet: Yes
- Typical Ignition Hardware: Q3450
- Approvals, American Gas Association IAS: IAS Design Certified: C2030017
Maintenance & Troubleshooting:
- This capacitor is typically replaced when diagnostics indicate a run capacitor is out of specification or when motor operation issues are traced to the dual run capacitor (diagnostic procedures are not provided in the supplied sources).
- If issues persist after replacement, confirm the installed capacitor matches the required MFD and voltage ratings and that all connections are correct per the equipment documentation.
Certifications & Compliance:
- Manufacturer listing states UL & cUL for these capacitors.
User Reviews & Q&A Summary:
- Review themes commonly describe it as a correct replacement capacitor that restores cooling operation when a failed capacitor is replaced.
- Many comments focus on getting the right part quickly and returning equipment to service, with frequent notes about straightforward replacement once the correct rating is confirmed.
Product Highlights
120v, 24V
Specs
| Product Type: | Control Board |
|---|
Â
Reviews
Clear filtersThere are no reviews yet.