Motors & Blowers
Thermostats
Breakers
Pilot & Ignitors
All products
New
The JOHNSTONE SUPPLY York S1-031-09156-000 is a fan/electric heat control board for HVAC systems. This control board is an OEM part from York, built to replace existing boards safely. It manages the operation of fan and heating components by distributing voltage as needed. The board continuously checks sensors and safety switches, making sure the HVAC system runs efficiently.
- OEM replacement for York HVAC systems.
- Controls fan and electric heat operations.
- Installation by licensed professionals is recommended.
Product Highlights
This board contributes to the overall efficiency of HVAC units and supports reliable operation.
Product Information
Standard Information
- Brand: York
- MPN: S1-031-09156-000
- Robust Push Terminals
- Common-Sense LEDs
- Clean, Professional Installation
- Smaller Footprint
- Variable-Speed Fan Control
- Includes HZ311 TrueZONE panel, AT140 40VA transformer, C7735A discharge air sensor
Product Specifications
- Stages: Single Stage
- Operating Voltage: Input 24 Vac, 60 Hz
- Line Voltage: 115-230 Vac, 60 Hz
- Inducer Motor/Blower Motor: PSC
- Ambient Operating Temperature: -40 to 175°F (-40 to 80°FC)
- Humidity Range: 5% to 95% relative humidity (non-condensing)
Product Specifications:
- Description: 1/2 in. NPT x 1/2 in. NPT Intermittent Hot Surface Pilot Ignition SmartValve Control with fast-fast opening and 3.4 in. wc pressure regulator setting
- Flame Sense: Electrode
- Type of Gas: Natural
- Ignition System Type: Intermittent Hot Surface Pilot Ignition
- Ignition Sequence: Intermittent Pilot
- Ignition Source: Pilot
- Ignition Trials To Lockout: Continuous Retry
- PrePurge: None
- Body Pattern: Straight-through
- Opening Characteristics: Fast-Fast Opening
- Ignition Trial Time (sec): 90 sec
- Electrical Ratings: 24 Vac
- Frequency: 60 Hz; 50 Hz
- Flame Failure Response Time (sec): 1.6 sec @ 3 µA
- Ambient Temperature Range (F): -40 F to +175 F
- Ambient Temperature Range (C): -40 C to +79 C
- Pressure Regulator Setting (psi): 3.4 in. wc
- Pressure Regulator Setting (kPa): 0.87 kPa
- Pressure Ratings (psi): 1/2 psi
- Pressure Ratings (kPa): 3.45 kPa
- Inlet/Outlet Size (in.): 1/2 in. NPT x 1/2 in. NPT
- Maximum Capacity (ft³/hr): 200 ft³/hr
- Maximum Capacity (m³/hr): 5.7 m³/hr
- Minimum Capacity (ft³/hr): 20 ft³/hr
- Minimum Capacity (m³/hr): 0.6 m³/hr
- Maximum Capacity at 1 in. P.D. (ft³/hr): 150 ft³/hr
- Maximum Capacity at 1 in. P.D. (m³/hr): 4.2 m³/hr
- Pilot Gas Outlet: Yes
- Typical Ignition Hardware: Q3450
- Approvals, American Gas Association IAS: IAS Design Certified: C2030017
Maintenance & Troubleshooting:
- This capacitor is typically replaced when diagnostics indicate a run capacitor is out of specification or when motor operation issues are traced to the dual run capacitor (diagnostic procedures are not provided in the supplied sources).
- If issues persist after replacement, confirm the installed capacitor matches the required MFD and voltage ratings and that all connections are correct per the equipment documentation.
Certifications & Compliance:
- Manufacturer listing states UL & cUL for these capacitors.
User Reviews & Q&A Summary:
- Review themes commonly describe it as a correct replacement capacitor that restores cooling operation when a failed capacitor is replaced.
- Many comments focus on getting the right part quickly and returning equipment to service, with frequent notes about straightforward replacement once the correct rating is confirmed.
Product Highlights
85/135V
Specs
| Product Type: | Replacement Part |
|---|
Â
Reviews
Clear filtersThere are no reviews yet.